375 mhz delay line 2.25 mhz bandwidth part number MN95029 idt ? ?? ? saw products ? ?? ? 324 clark street, worcester, ma 01606, usa ? ?? ? ph 1-508-852-5400 ? ?? ? fax 1-508-852-8456 www.idt.com dsMN95029 rev - 21-oct-2008 ecn 36187 page 1 of 3 description ? 375 mhz saw delay line with 2.25 mhz bandwidth. ? 5 x 7 mm ceramic lcc. ? rohs compliant. typical performance s11 (365C385 mhz) s22 (365-3 85 mhz) amp10 db/div amp1 db/div phase10 deg/div delay100 ns/div center = 375 mhz, 2 mhz/div (25 khz incr)
375 mhz delay line 2.25 mhz bandwidth part number MN95029 idt ? ?? ? saw products ? ?? ? 324 clark street, worcester, ma 01606, usa ? ?? ? ph 1-508-852-5400 ? ?? ? fax 1-508-852-8456 www.idt.com dsMN95029 rev - 21-oct-2008 ecn 36187 page 2 of 3 specification parameter min typ max units center frequency (fc, at 10db points) 2,3 374.90 375 375.10 mhz insertion loss - 10.7 12 db 3 db bandwidth 2.15 2.35 - mhz 10 db bandwidth - 4.06 4.4 mhz phase linearity (373.9-376.1 mhz) 2 - 3 10 deg p-p phase slope (in 3 db bw) - -0.16 - deg/khz group delay ripple (373.9-376.1 mhz) 2 - 25 80 nsec p-p insertion phase 1, 2 - 0 - deg device delay - 430 - ns turn over temperature (tc) - 53 - c source and load impedance - 50 - ambient temperature - 23 - c notes: 1. measured at 375 mhz in a tuned reference test fixture. 2. specifications apply at an ambient temperature of 23c +/- 5c. 3. frequency versus temperature will be according to the following: dfc/fc = -0.032 ppm * (t-tc) 2 where (dfc/fc) = change in center frequency (in ppm ) and t = temperature (in degrees c). tc = the turnover temperature. maximum ratings parameter min max units storage temperature range -40 125 ?c operating temperature range -30 100 ?c input power level - +13 dbm matching circuit typical component values: notes: 1. recommend use of 2% tolerance matching componen ts. typical inductor q=40. 2. component values are for reference only and may change depending on board layout. ls1 = 64.2 nh ls2 = 56 nh cp1 = 18 pf cp2 = 18 pf 12 6 all others input 50 single-ended output 50 single-ended gnd gnd
375 mhz delay line 2.25 mhz bandwidth part number MN95029 idt ? ?? ? saw products ? ?? ? 324 clark street, worcester, ma 01606, usa ? ?? ? ph 1-508-852-5400 ? ?? ? fax 1-508-852-8456 www.idt.com dsMN95029 rev - 21-oct-2008 ecn 36187 page 3 of 3 package outline suggested footprint iso 9001 registered all specifications are believed to be accurate and reliable. however, mnc reserves the right to make changes without notice. ? 2008 all rights reserved. package material: body: al 2 o 3 ceramic lid: kovar, ni plated terminations: au plating 1 em min, over a 1.3-8.9 em ni plating units: mm tolerances are 0.15 mm except for the overall length and width, which are nominal values. pad configuration: input: 12 input return: 10 output: 6 output return: 4 ground: all other pads ? idt MN95029 xxxxx yyddd
|
